FEATURES |
|
■ |
Wow flutter measurements possible in accordance with different standards for RMS, NAB at 3kHz and for IEC (DIN/CCIR) at 3.15kHz. |
■ |
Wide wow flutter range, 0.001% to 3%, for accurate measurements for all classes of recording/playback equipment. |
■ |
Measurements can be made under weighted and unweighted conditions; in addition, wow and flutter can be separately determined. |
■ |
At IEC(DIN/CCIR) measurements, a sigma memory for three modes, 1σ, 2σ, and 3σ, enables readings at the hold condition of the meter. |
■ |
FIN (Frequency Intermodulation) measurements in accordance with DIN45411 are possible. |
Center Frequency Range |
3kHz ±300Hz and 3.15kHz ±300Hz |
|
Input Level |
0.1mV to 10Vrms : Two ranges
0.1mV to 30mVrms, 5mV to 10Vrms
|
|
Input Impedance |
300kΩ ±20%, unbalanced |
|
Measurement Range |
0.0015% to 3% in 6 ranges: |
(However 0.1 to 30mV ranges is 0.003 to 3%) |
0 to 0.01% , 0 to 0.3% , 0 to 0.03% , 0 to 1% , 0 to 0.1% , 0 to 3% |
|
Indication Modes |
Effective value for RMS, average value for NAB and peak value for IEC (DIN/CCIR). |
|
Indication Accuracy |
±5% of full scale at 4Hz on all ranges. |
|
Frequency Characteristic |
Weighted |
0.2 to 200Hz for JIS, NAB and IEC (DIN/CCIR) |
Wow Flutter |
• Wow |
0.5 to 6Hz |
• Flutter |
6 to 200Hz |
Unweighted |
• NAB |
0.5 to 200Hz -3dB±1dB |
• IEC(DIN/CCIR) |
0.3 to 200Hz -3dB±1dB |
Roll off |
• NAB |
-6dB/oct below 0.5Hz |
-15dB/oct above 200Hz |
•IEC(DIN/CCIR) |
0.3 to 200Hz, -3 ±1dB |
-6dB/oct below 0.3Hz |
-15dB/oct above 200Hz |
|
FIM (Frequency Intermodulation) Measurement |
Range |
Corresponding to wow flutter measurement |
Filter Characteristics |
• FIM at ON |
Low pass filter |
-3 ±1dB at 500Hz |
Roll off |
-36dB/oct above 500Hz |
• 160Hz Filter at ON |
High pass filter |
-3 ±1dB at 100Hz |
Roll off |
-12dB/oct below 100Hz |
|
Tape Speed Indication |
3 ±1kHz : 4-digit display |
|
Measurements With Memory |
Method |
Sigma memory for IEC |
Peak-hold for JIS, NAB, IEC |
Driving |
Manual, repeat and automatic control with input monitor.
(Manual or repeat operation when input signal is applied.)
|
Sigma Mode |
3 points? 1σ, 2σ and 3σ |
Measuring Time |
2.5 sec crystal-controlled |
Memory Read Time |
Approx. 2 to 6 seconds, variable, with internal adjustment |
Preparation Time |
For automatic control with input signal : 1 to seconds, variable, with internal adjustment. |
|
Wow Flutter Digital Indication |
(Counter display during readout time at memory measurements.)
|
Display |
3 digits, effective, at 3%, 0.3% and 0.03% ranges. |
2 1/2 digits, effective, at 1%, 0.1% and 0.01% ranges. |
Accuracy |
±(2% +1 digit) at full scale. |
Display Time |
Corresponds to memory readout time.
|
|
Recording Signal Source |
Frequency |
3kHz and 3.15kHz ±3×10-5 (crystal controlled)
|
Output Voltage |
Approx. 0.2Vrms at open circuit |
Output Impedance |
Approx. 600Ω unbalanced |
Distortion |
Less than 0.5% |
|
Drift Signal |
Output Voltage |
±1.0V ±10% per ±1% drift |
Output Impedance |
600Ω ±10%, unbalanced |
|
Recorder Signal |
Output Voltage |
±1.0V ±10% per ±1% drift |
Output Impedance |
600Ω ±10%, unbalanced |
|
Flutter Signal |
Output Voltage |
±1.0V ±10% per ±1% drift |
Output Impedance |
600Ω ±10%, unbalanced |
|
Flutter Signal |
Output Voltage |
+5V (TTL level) |
|
Frequency Counter (When used independently) |
Range |
10Hz to 99.99kHz in 2 ranges |
0.01 to 9.999kHz and 0.1 to 99.99kHz |
Accuracy |
±(1count + ref. Frequency accuracy) |
Reference Frequency |
600kHz ±1×10-4 : crystal-controlled |
Input Voltage |
100mV to 10Vrms |
Input Impedance |
Approx. 300kΩ, unbalanced |
Measurement Time |
2 ranges: 0.1 and 1 sec |
Display |
4-digit |
|
General Data |
Operating Temp. |
Range 0 to 40ºC
|
Power Requirements |
100V, 115V, 215V or 230V
50/60Hz (voltage selector provided)
Approx. 25VA |
Dimensions, max |
Approx. 360(W)×165(H)×290(D) mm |
Weight |
Approx. 6kg |
|
* |
Specifications are subject to change without notice.
|
|
|