Zero Gauss Chamber Alphalab
Product Description:
The model ZGC zero gauss chamber reduces the environmental magnetic field (Earth field) to near zero inside the chamber. Any gaussmeter probe which is less than 9.4 mm or 0.370″ diameter can be placed inside. The meter is then “zeroed”, which means that it will read zero whenever the probe is subsequently placed in zero field. By using a zero gauss chamber, any offset error is therefore eliminated. The model ZGC is unique in that it contains a degausser (demagnetizer). This is situated between the inner and outer mu-metal shields. When the degauss button is pressed, any accidental magnetization of the chamber, no matter how strong, is erased. Accidental magnetization is a major problem with most zero gauss chambers and it has limited their use. If a magnet comes too close, the chamber will become “permanently” magnetized and will have an internal field that is typically 0.2 to 0.5 gauss. The chamber must then be degaussed because the Earth field is also around 0.5 gauss, so a magnetized zero gauss chamber will not significantly reduce the field.
Demagnetizing a zero gauss chamber with an external degausser is difficult, even if a degausser is available. Often an external degausser is not strong enough to erase the magnetism of the inner shield, and using a degausser (which is fairly large) is not convenient. When using the ZGC, a single press of the degauss button brings the internal field to less than 0.01 gauss (in all three axes) within a 5 mm wide x 9.4 mm diameter region in the center of the chamber. While the battery is connected, no power is consumed except when the degauss button is being pressed. Even then, a typical 9 volt battery (included) can power over 10 million degauss cycles. After degaussing, the field is < 0.01 gauss regardless of the orientation of the chamber (within the Earth field). If the long axis of the chamber (left-right direction in photo below) is specifically oriented east-west during the degauss, the internal field will be < 0.002 gauss, although most gaussmeters do not require that degree of precision.
The white cylindrical spacer (shown in hand below) is included. It is used as a “stop” to center most gaussmeter probes in the zero gauss region. It allows the end of a probe to be inserted 1.6 mm past the centerline of the chamber. This is the appropriate distance for exact centering of all AlphaLab gaussmeter probes, including axial, transverse, universal and 3-axis. The spacer can be inserted in either side (the chamber is symmetric).
AlphaLab Zero Gauss Chamber (ZGC) Instructions
The white plastic part (spacer) can be removed at any time, but it should be used if you want to center a gaussmeter probe inside the chamber. When placed in either end, this white spacer will allow the end of a probe to be inserted exactly 1.6 mm past the center of the chamber. Therefore the actual sensor for AlphaLab models VGM, GM-2, GM-3, 1-ST and 1-HS will be properly centered in the chamber. The zero gauss region has diameter 9.4 mm (0.370”) and occupies the center 5 mm (0.197”) within the chamber. (The chamber dimension in its long axis is 36 mm, or 1.42”). In the center 5 mm, the magnetic field is < 0.01 gauss after pressing the black degauss button, regardless of the orientation of the chamber. It will remain < 0.01 gauss as long as the chamber is not rotated more than 30 degrees from its orientation when degaussed. (Note that this specification is valid if the field outside is <0.6 gauss, which is characteristic of the Earth field.) Insert the gaussmeter probe as shown below and zero the gaussmeter.
The field inside the chamber can be reduced to < 0.002 gauss (2 milligauss) if the long axis is oriented the east-west direction when the degauss button is pressed, and if the chamber is kept in that orientation. However, 0.002 gauss accuracy is not necessary for most gaussmeters, which generally read down to 0.01 or 0.1 gauss.
Công ty CP Công Nghệ Đỉnh Cao
Trụ sở: Số 12 Chân Cầm, Hàng Trống, Hoàn Kiếm, Hà nội
VPGD: Phòng E2, Tòa nhà C4, Đường Đỗ Nhuận, Xuân Đỉnh, Từ Liêm, Hà nội
Tel: +84 (4) 22428148; Cel: 0984843683,Fax: +84 (4) 37505143
VPGD: Tầng 19, Tòa nhà Indochina/ Số 4, Nguyễn Đình Chiểu, P.Đakao, Q.1,
TP Hồ Chí Minh..
Tel: 08.6685 8911 Fax: 08.6284 0993.
Website: www.ttech.vn, www.store.ttech.vn, www.tshops.vn, www.stock.ttech.vn, http://www.omega-air.vn/