Compliance LCT-601 Hipot/Ground Bond function Tester

Mã sản phẩm:	LCT-601
Sử dụng cho Model:
Hãng SX:	Compliance
Xuất xứ
Bảo hành
Tình trạng

Tình trạng: Còn hàng

Số lượng:

Đặt hàng

Liên Hệ Hỗ Trợ

- SĐT: 0984 843 683
- Mail: info@ttech.vn
- - Zalo: 0984.843.683

Thông tin sản phẩm

Features

LCT-601 Hipot/Ground Bond function Tester
Provide a fast, safe and reliable method of performing production-line and field testing of leakage current and ground path resistance.
Minimize cost by using a true RMS multimeter.
Saves time by including all test switch permutations and its easy to configure.
Reduces the potentially dangerous risks associated with other test methods.
Quickly and easily performs resistance and leakage measurements
Provides compliance to:
NFPA 99-1999 sections 7-5.1.3.2 to 7-5.2.2.1 for resistance and leakage testing of field-installed equipment NFPA 99-2002 sections 8.4.1.3.2 to 8.4.2.2.1)
NFPA-99 section 9-2.1.13 for production resistance and leakage testing (NFPA-2002 section 10.2.13)
UL and IEC 60601-1 leakage testing
4 switches allow all common tests to be performed no complicated calibration necessary - requires only a verification of internal component values
Used with your existing multimeter (not provided) for increased versatility and cost savings
Portable, lightweight. Measures 6.6 x 5.3 x 2.3 in.
Custom leads and connectors available
Custom body-simulator circuits available
Ergonomically designed for safety, speed and efficiency
No batteries or power required

Item	Name	Function
1	Polarity switch	Used to reverse the polarity of the output power to the EUT (line and neutral are swapped). EUT should comply with the required leakage current limits in Normal and Reverse polarity.
2	Neutral switch	Used to disconnect the Neutral of the incoming power (before the polarity switch). Leakage currents are generally higher with the Neutral open; many standards and requirements specify that the Leakage measurement be made with the Neutral open as a single-fault condition (higher leakage limits apply). In normal conditions this switch is left in the Neutral Connected position.
3	Earth-Chassis switch	In the Open position, used to disconnect the incoming ground from the output ground in order to make leakage current measurements. In the Closed position, the incoming ground and the output ground are connected together.
4	Measurement point switch	Used to select where the leakage measurement is being made. In the Chassis position, the leakage measurement is made from the output ground to the incoming ground. In the Floating position, the leakage measurement is made from where the floating measurement point is connected by the operator (to the EUT), to the incoming ground.
5	Leakage measurement connection point	Your external calibrated meter is connected to terminals 5 and 6 . Set the meter to read "millivolts AC" The displayed reading will be 1 millivolt for each milliamp of leakage current.
6	Input Ground (circuit common)	Used as the common point for leakage measurements. To measure the resistance from any point to the incoming (building) ground, turn switch 3 to "Open", and connect a resistance meter to this jack, and the other end of the resistance meter to the point to be measured.
7	Output Ground	To measure the resistance from the ground wire of the EUT to any other point, turn switch 3 to "Open", and connect a resistance meter to this jack, and the other end of the resistance meter to the point to be measured.
8	Floating measurement point	Used to measure the leakage from any point on the EUT when switch 4 is in the "Floating" position. This is typically used to measure leakage from ungrounded parts or patient- contact parts.